Notes
- Which setting is by default.
- default setting is the "accurate mode"
- Which presets are available by uploading.
- Survey-in mode, minimal position accuracy and minimal survey-in time, both parameters need to be met before the base station is measured in.
- fast mode
- normal mode
- accurate mode
- after survey-in is complete, the accuracy is fixed and will remain constant. If a higher accuracy is required, it is recommended to use the "accurate mode".
- fixed mode, will send out RTK messages based on a fixed GNSS location, so only takes into
- requires precise location survey-in and a fixed position of the base station. for example, let the base station survey-in for >24h on a day with clear skies and on a spot with minimal obstructions for the GNSS antenna. The result is an averaged out location based on this base station only. Take note of the Longitude, Latitude and Altitude of the base station and use as input for the "fixed-mode" under UBX > CFG (config) > TMODE3 (Time Mode 3).
- There are more advanced methods where a >24h data set of the base station can be used to determine millimeter accurate position of the base station. This can be done using a Precise Point Positioning (PPP) service. Please contact Avular if you would to pursue this functionality.
- Correction Data Generation: Based on its fixed position and satellite signals, the base station calculates the errors in the satellite signals it receives (e.g., atmospheric delays, satellite clock errors, and orbit errors) and broadcasts these as RTK correction data.
- can also be used when power is removed from base station, yet it must remain on the exact same position. it can start sending out RTK messages from the fixed mode.
- user must first deploy survey-in mode in accurate mode, wait for at least 24 hours and denote the coordinates,
- recommended to have a permanent fixture for the base station that cannot be moved. For example, a tripod mount that is attached to a roof. Or mark the position of the tripod
- requires precise location survey-in and a fixed position of the base station. for example, let the base station survey-in for >24h on a day with clear skies and on a spot with minimal obstructions for the GNSS antenna. The result is an averaged out location based on this base station only. Take note of the Longitude, Latitude and Altitude of the base station and use as input for the "fixed-mode" under UBX > CFG (config) > TMODE3 (Time Mode 3).
- Survey-in mode, minimal position accuracy and minimal survey-in time, both parameters need to be met before the base station is measured in.
-
How to set different settings.
- ensure the base station is powered by the power supply
- insert a usb-c cable into the base station and connect to a laptop
- open ucenter software suite
-
Use of Ublox U-center software suite
- download u-center from the official website
- ensure to download "u-center" and not "u-center 2", the latter is not compatible with the base station
- how to install on windows
- how to install on linux using wine
- download u-center from the official website
Check status survey-in:
messages view > UBX > NAV > SVIN (survey-in), select and then right-click & enable message --> can now visualize how it updates continously
Check which setting the base station is set to:
messages view > UBX > CFG (config) > TMODE3 (Time Mode 3), select and to update display right-click and poll message
Setting your desired settings for survey-in or fixed mode, remember to press "send" on the lower left corner.
Quick Start Guide: Brief instructions for users who want to get started quickly.
-
Choose a proper position to set up the base station: this is a position open to the air with at least 10 meters distance from buildings, trees and/or other tall structures near the location.
-
Fully assemble the base station: place the station on the tripod and install the antennas. Make sure the antennas are connected to the correct connectors: the smaller dipole antenna to "1. DATA ANT"-connector and the large GPS round antenna to "2. GNSS ANT"-connector.
-
Power the base station by plugging in a power source in the PWR connector. Always power up the base station after placing it on the location and do not move it afterwards. Power status is shown by a green LED on the right side of the LED-bar. When the red LED in the middle of the LED-bar is on, then the GNSS receiver is active.
-
The device will now start receiving GNSS data and learning its position. This postion will be bused to create RTK correction messages. GNSS reception is shown by a blinking blue LED in the middle of the LED-bar
-
Between a few seconds and a few minutes the position is learned. On an overcast day the time will be increased.
-
A blinking green LED on the left side of the LED-bar shows that the radio is transmitting messages. This will also include the RTK correction messages when the position of the base station is learned.
System Requirements
- Compatible with Avular Origin and Vertex robots
- Operates on AC power using the included power adapter or with an 8-40V DC power supply
- Open area with minimal obstructions for optimal performance
Quick Start Guide
- Choose a Proper Position: Select an open area with at least 10 meters of clearance from buildings, trees, and other tall structures.
- Assemble the Base Station:
- Place the base station on the tripod.
- Install the antennas: connect the smaller dipole antenna to the "1. DATA ANT" connector and the large GPS round antenna to the "2. GNSS ANT" connector.
- Power the Base Station:
- Plug in the power source to the PWR connector.
- Ensure the base station is powered up after being placed in position and avoid moving it afterwards.
- The power status is indicated by a green LED on the right side of the LED bar. The red LED in the middle of the LED bar indicates that the GNSS receiver is active.
- Start Receiving GNSS Data:
- The device will begin receiving GNSS data and learning its position.
- Ensure the base station remains stationary during this process for accurate positioning.
By following these steps, you can quickly set up and deploy the RTK GNSS Base Station to provide high-precision positioning data for your Avular robots, enhancing their outdoor navigation capabilities.
Status indication
LED bar image? Status 1, left LED solid = power blinking = RTK messages transmission??
Status 2, middle LED GNSS receiver activ red = GNSS receiver active
Status 3, right LED GNSS reception?
Base configurations
Note the 3 different configurations and use-cases. Link to configuration page for configuring the base station to settings
TODO: - how to see if the measure in is done? --> blue light? - how to transport --> remove quick-release - link to origin platform display, to see the state of the RTK - explanation on how to assess the current RTK status in ROS topic from the user container